- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Re: No volume exists
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi,
I have a Readynas RN10400 with firmware version 6.9.4
It has 4 x Seagate NAS ST3000VN000 disk drives orginally X-RAID but since issue the system shows RAID 5 and zero free space.
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi davidburchett52,
You may download the logs and upload it to a file sharing site then PM me the download link. We may be able to check what would cause the volume to become inactive.
I also agree with @StephenB that it will be best to contact NETGEAR support so they can assist you in finding what caused the issue and with the data recovery as well.
Regards,
All Replies
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
I think your best option is to contact paid support via my.netgear.com.
FWIW, it sounds to me like your NAS is used for primary storage, not really as a backup device.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi davidburchett52,
You may download the logs and upload it to a file sharing site then PM me the download link. We may be able to check what would cause the volume to become inactive.
I also agree with @StephenB that it will be best to contact NETGEAR support so they can assist you in finding what caused the issue and with the data recovery as well.
Regards,
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
Thanks for your replies guys...
I've got the NAS working again but have one remaining issue that I've seen in other posts, one of my disk's (the newest one) is triggering the following error message in the log:
Disk: Detected high uncorrectable error count: [3392] on disk 4 (Internal) [ST3000VN000-1HJ166, W6A1GT98]. This condition often indicates an impending failure. Be prepared to replace this disk to maintain data redundancy.
I plan to make a copy of all my data then run tests on the disk 4 and also reset the NAS back to factory default before copying the data back on to the NAS.
If the errors on disk 4 continue I'll open a new ticket.
Thanks again for your responses.
David
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
@davidburchett52 wrote:
Disk: Detected high uncorrectable error count: [3392] on disk 4 (Internal) [ST3000VN000-1HJ166, W6A1GT98]. This condition often indicates an impending failure. Be prepared to replace this disk to maintain data redundancy.
This error is being reported by the drive - the NAS is just forwarding the problem to you. It's most likely an early failure in the drive itself.
So test the drive in a Windows PC with Seatools. You can connect it either with SATA or a USB adapter/dock.
If you just purchased the drive, you could also just exchange it with the seller for a new one.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
Thanks Stephen,
That's exactly what I intend to do and will report back with the results.
Data transfer is incredibly slow using widows explorer, three days so far and only 16% through a 2.15 TB folder/share...
All the best
David
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
@davidburchett52 wrote:
Data transfer is incredibly slow using widows explorer, three days so far and only 16% through a 2.15 TB folder/share...
That's likely related to the failing drive. Is the system also syncing the array?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
Hi Stephen,
Yes it could be the drive I guess, will find out in due course. As far as the array goes, I've disabled any further backup jobs and turned off snapshots so I assume there's no acivity?
Cheers
David
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
@davidburchett52 wrote:
As far as the array goes, I've disabled any further backup jobs and turned off snapshots so I assume there's no acivity?
There are other things that could be going on. For instance, the array could be syncing, or a maintenance function (including the new auto defrag option) could be running.
You could also turn off Antivirus for now.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
Hi:
I have the same problem.
How do you resurrect your Disks?
Thank you in advance.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
@vialta wrote:
I have the same problem.
How do you resurrect your Disks?
If your system won't boot, then start by testing them.
If you have access to a Windows PC, then power down the NAS, and remove the disks (labeling by slot). Then connect them to the PC (either with SATA or a USB adapter/dock), and test them with vendor tools. That would be lifeguard for western digital and seatools for seagate. I don't recommend letting the diagnostics repair the disks - just test them.
If your system is booting, then download the logs. You can PM @JohnCM_S or @Marc_V and ask them to analyze them for you. Don't post a link to your logs publicly here.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
Thank you very much for your reply, I'll try and see if that works.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
OK so I've got all my data off and ready to do a factory reset, I'm running OS 6.9.5.
Before I hit the reset switch I'd just like to check a couple of things.
- The system is reporting a high uncorrectable error count [2352] on one disk - Should I try and fix, replace or run any tests on this disk before or after the reset?
- Do you know of any gotcha's when it comes to performing a factory rest on this device/OS version?
Cheers
David
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
@davidburchett52 wrote:
- The system is reporting a high uncorrectable error count [2352] on one disk - Should I try and fix, replace or run any tests on this disk before or after the reset?
I wouldn't use a disk with this error count (and I wouldn't attempt to "fix" it either").
Personally I'd replace it with the NAS powered down, and do the reset using the boot menu.
@davidburchett52 wrote:
- Do you know of any gotcha's when it comes to performing a factory rest on this device/OS version?
No. The procedure is documented on pages 28-29 here: http://www.downloads.netgear.com/files/GDC/READYNAS-100/ReadyNAS_%20OS6_Desktop_HM_EN.pdf
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
Might be a gotcha when doing a factory reset for this model/OS afterall...
Following the factory reset the front panel is showing the message "putname+14" and the power button is unresponsive!
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
If you can connect the disks to a Windows PC, you can zero them with the "write zeros" test in WDC's lifeguard program. There's a quick-zero option that will also work.
Then put the disks back in the NAS and power up. The NAS will do a factory install when it detects the disks are unformatted.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
OK so WDC Lifeguard and Seatools were unable to write to the drive so I got the dive wiped in Windows Disk Management.
The disk is now back in the NAS and following an initial Data Degrade message on the front CP it is now recovering data.
I suspect it's rebuilding the array but I would rather it be restored to factory state as I no longer need the data and would like to start afresh with a clean system/drives.
What's the next step, Turn it off then perform another factory reset or wait untill it's finished recovering data and then do the factory reset?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
@davidburchett52 wrote:
OK so WDC Lifeguard and Seatools were unable to write to the drive so I got the dive wiped in Windows Disk Management.
That's weird, and suggests that something might be wrong with the drive. What's the model number (and manufacturer)?
@davidburchett52 wrote:
What's the next step, Turn it off then perform another factory reset or wait untill it's finished recovering data and then do the factory reset?
I'd let the resync finish and look at the SMART stats - confirming that the drive is actually ok.
You can then do a factory reset from the boot menu (or alternatively from system->settings in the web ui).
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
Drives are all the same, Seagate NAS ST3000VN000 and the one from drive bay 4 that the NAS was reprting errors on was removed and tested using Seatools and WDC Lifeguard. The drive passed all tests incluing the long ones but niether of these tools were able to write to the drive, I suspect because it was locked by the NAS OS RAID application. So, I used Windows 10 disk to wipe it and that worked fine. Popped it back in the NAS and as mentioned it started to rebuild, currently at 8% after 12 hrs, going to be a long wait before I can do another factory reset?
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
@davidburchett52 wrote:
I suspect because it was locked by the NAS OS RAID application.
The NAS application shouldn't lock the drive. And if it had locked it, Windows wouldn't have been able to format it either.
So something else went (or is) wrong.
FWIW I have had drives that passed the non-destructive tests, but which failed the write-zeros test. If you did a quick format in Windows it doesn't write to much of the drive - just enough to create the file system.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Re: No volume exists
Just to let you know that the unit has been factory reset and running like new again, Seagate replaced my faulty 3TB with a new 4TB drive and although I don't see any more storage it seems to be getting on with the other three 3TB drives without any issues. Thanks for your help and assistance as we've worked through this issue.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content