NETGEAR is aware of a growing number of phone and online scams. To learn how to stay safe click here.
Vlan Combine when Partition Walls controlled QSC
Looking for info/ help. We are using a M4250-26G4F-POE+ with a QSC core to Combine 2/3 meeting room together. We are using a Huddly Crew Cameras (poe) . I'm looking to Combine 3 Different Vlans together to combine all the cameras Is there a Easy way or Do I need to use command line prompts to allow / deny vlan controlling?POST Issues GSM4248UX
Hi, the power on start of self teset on my GSM4248UX is failing. I power on the switch and it starts with the test. All of the ports in the back of the unit light up for a few seconds. The power LED blinks a number of times then stays on red solid light. The switch is not accessible via the OBB or any of the ports. The switch was working fine for a day or tow, but then we updated the software to the latest firmware. V13.0.5.24 Then we started having this issue. I have tried the paper clip reset multiple times, but there are no indications that this is working at all. Any comments will be greatly appreciated.
M4300 (GSM4352PS V1) : can't get kernel image
Hi Netgear Users and Administrators, I have a little problem with my M4300 GSM4352PS V1. There's possibility that image2 is broken. Device is actually booting from image2. On the console I see that can't boot from image and i see "ERROR: can't get kernel image". I supose that the image1 is a good conditional. Best Redgards PawelAV VLAN uplink to public manage switch
Hi All: At our educational facility we are redesigning an existing 2 x room AV system with "cross-room" Audio Visual broadcast connectivity using Crestron Digital Media architechture Each room has a dedicated Crestron DMPS-4K-350-C + DMPS-4K-250-C units with with TV displays, Microphones and Camera's. We have a new Audio Visual private VLAN link between 2 x rooms using core Netgear AV Line switches being programmed for the Crestron Graphic User Interface control in each space. Netgear M4250-9G1F-PoE+ network switch (smaller room 1) + Netgear M4250-26G4F-PoE+ (GSM4230P (larger room 2) My question is for how we can securely manage the AV endpoints inside the private AV VLAN? Crestron virtual X-panel touch screen control is needed + two DMPS hardware units, Biamp audio processors; we need IP control into this new private AV-VLAN from our existing public managed Switch local subnet. I would like to create an ethernet patch uplink from the core Netgear M4250-26G4F-POE (same AV system rack as our Crestron Managed switch) into our local managed public subnet switch which is a Crestron CEN-SW-POE16 Any thoughts on the best way to configure this would be appreciated. Thank youEngage Onboarding Issue
We have 15 M4250 switches running our AV network. Recently, we realized two of those switches were assigned the same IP. Because of this, only one of the devices was showing on the Engage Dashboard. We did a hard reset on one of the switches (the one that was showing) so that we could assign it a new IP. Now the one switch that I reset will not show in Engage. I went through the Main UI to assign it a new IP address and when entering that IP into "Add Device" on Engage, I'm met with the message that the "device is already onboarded". How can I clear it from onboarding so I can set it up as a new device? Or at the very least, get it to show in Engage?GSM4328S spuriously after powering up, shows power led amber on, and stucks
M4300 (GSM4328S) spuriously after powering up, shows power led amber on, and stucks. Need to disconnect and connect again power supply, and then works. I don't know if someone is experiencing this issue. Maybe is a hardware issue. We are using lots of those switches for several different projects in our company, and we are experiencing in the last purchased units (more than 20) this upsetting issue. We don't know how we can diagnose the problem. Anyone could help us?Creating and setting up a VLAN
Hi, I have a network 192.9.200.0/24. I need to access a device using 192.9.201.0/24 I am using a M4300-12X12F ProSAFE 12-port 10GBASE-T and 12-port 10G SFP+ with firmware 12.0.4.8. I could not create a VLAN with the GUI, the Switching -> VLAN Config -> Advanced "Add" button was not working. Any idea why? Instead, I used the CLI with (On Windows 10): telnet 192.9.200.217 enable vlan database vlan 100 I am stuck on assigning a 192.9.201.217 IP address to VLAN0100 and setting up the routing between default and VLAN0100. How do I do that, preferably with the GUI?