Showing ideas with status New Idea.
Show all ideas
Hi,
This idea is for Access Point WAC 505/510. The product is not in the list.
In standalon mode, I can schedule different activation times of the wifi.
In Insight Mode, the option disappears and it's impossible to do this.
I can not believe Netgear forgot that. Netgear support and the sales department told me whether or not the POE was enabled on the switch port. It's a joke ?
The scheduling option must be implemented. At the moment, I'm using my WAC505 in standalone mode.
... View more
See more ideas labeled with:
Dear ladies and gentlemen,
I have several Netgear Switches. Two of them are the GS750E and the JGS524Ev2.
I am using port-based VLANs and wanted to create a 4-Port LAG connection between them.
On the GS750E I create a LAG with 4 ports as port members.
After that I remove the ports that are members of the LAG from the VLAN and add the LAG to the VLAN instead.
the GS750E has FW Version 1.0.0.22.
When I want to do the same on the JGS524Ev2 there is no possibility under "VLAN/port-based/advaced" to add the LAG to the VLAN.
It would be very great if you could realize this feature in the next FW release of the JGS524Ev2. I am just using the latest FW!
Thanks a lot !!
... View more
See more ideas labeled with:
I want it to be able to set up a list of allowed devices (by MAC address) for wired access, but still allow any device to connect through the guest portal. Ideally, one could have separate allowable MAC lists (or allow all) for each wireless SSID in addition to the wired access. Maybe a table with MAC address and then a checkbox for Wired, Wireless1, Wireless2, and Guest to show where it is allowed to connect.
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2019-02-04
09:48 PM
Submitted by
MarcVanBracht
on
2019-02-04
09:48 PM
Hi all,
(NO INSIGHT harware selectable... therefor this WAC730)
INSIGHT has now the possibility tp maken backups of the hardware in INSIGHT
However, you have to make them mannualy.
I suggest to create a "scheduled backup" i.g daily or weekly or monthly so you have always a "latest backup" available.
With 10 or more sight/locations in INSIGHT is is impossible to maken backups mannualy.
Marc van Bracht
Nox Telecom
The Netherlands
... View more
See more ideas labeled with:
Hi, As a common use-case tor these PoE switches is CCTV with connections outdoors, may I suggest to add a feature in the firmware that prevents these outdoor ports to be used with devices other than the intended camera? Would port-security, ie. binding to a given MAC address, be a right step in that direction? Or did I overlook a feature that already does this now? I'm by far not an expert 😉 Kind regards, C.
... View more
See more ideas labeled with:
We need to have the ability to assign SSIDs to VLANs for true buisness functionality.
... View more
See more ideas labeled with:
It would be a wonderful feature if the switch would show you the MAC address table it's using. This feature is the only thing missing from making this a great switch.
Thanks!
... View more
See more ideas labeled with:
Add management VLAN support on 5 port ProSAFE Web-Managed switches.
... View more
See more ideas labeled with:
Hoping that a whitelist of MAC address will be included. One for Employee and one for guest network.
Credits to @bek_gto for this idea.
In reference to this community thread.
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2018-12-18
02:01 PM
Submitted by
robertpankrath
on
2018-12-18
02:01 PM
Dear developers,
it would be great to be able to configure VLAN for management only.
See also this thread:
https://community.netgear.com/t5/Smart-Plus-Click-Switches/GS108Ev3-Cannot-set-VLAN-for-management-interface/td-p/971240
If that is too much work could you please implement the possibility to disable Webif with Plus Utility?
Reason for this is to get rid of this limitation /unpleasant behaviour:
"To support WEB GUI, all HTTP packets are forwarded to the embedded CPU. With Flow Control enabled, throughput will be impacted if the rate is higher than the CPU can handle."
or at least having a workaround to avoid it!
Kind Regards
Robert Pankrath
Berlin Germany
... View more
See more ideas labeled with:
Currently running V2.2.1.210 on an Orbi Pro SRR60 (an additional thing would be to actually order the Model field in this form, i couldnt find Orbi Pro in it).
The traffic meter today shows only the total traffic flowing through the router. Any router that is labeled "pro" and is sold for business purposes should include a report that shows traffic by IP and traffic by service type.
... View more
See more ideas labeled with:
HI,
I want to open new office soon and requesting for suggention on powerline ethernet adapter to use.I dont want run CAT6 cable all over office & dont want to use wifi solution.Total office desk will be around 140-170.
Please give me your suggestion to use power line networking with 170 computers.I have file server & active directory .....
Online its showing only for home network.But I want to use same technology for office network.
Please let me know the pros and cons.
Thank you.
https://www.netgear.com/home/products/networking/powerline/default.aspx
... View more
See more ideas labeled with:
Hi
I would appreciated if you would develop any access point (like Wi-Fi router) that supports Wi-Fi Round Trip Time (RTT), via IEEE 802.11mc.
Joakim Almström, developer ASSA ABLOY
... View more
See more ideas labeled with:
The GS110TP supports only a max SSL key length of 2048 bits. This is a real problem for modern PKI infrastructures where - at least - the CAs almost always use a 4096 bit key length.
Given that the GS110TP is still sold today I hope hat this could be corrected in a (near) future firmware update.
... View more
See more ideas labeled with:
The BR500 comes only with Port Forwarding. It needs a 1:1 NAT feature similar to the FVS338 firewall device. Port forwarding is not a viable solution since my business deals with static public IP addresses that need a hard 1:1 assignment to an internal NATed address assigned to a server (e.g., Exchange Server, IIS, etc.). The FVS338 feature/facility worked great - just copy it into the BR500.
... View more
See more ideas labeled with:
We're missing the ability to generate CSRs with 2048 bit on the Netgear Business products (like the Smart Manged Plus, Smart Managed Pro, Managed Switches, coming-up Routers like the BR500, and solo the ability to generate self-signed certificates accordingly.
... View more
See more ideas labeled with:
(I actually have the 48 port model but that wasn't in the drop down list.)
I ran into a problem when trying to get a legitimate (as opposed to self-signed) CA certificate. The CSR that this switch generates is 1024 bit and my CA issuer requires 2048 bits minimum. I would like to request a larger range available for CSR generation so that I can get a good CA certificate for the switch. This could be easily done with a drop down giving the user a choice between 1024, 2048, 4096 etc bits to use in the private key and CSR thusly generated.
I have witnessed other infrastructure become slowly more difficult to access because modern browsers are demanding more stringent standards for the certificates they recognize; I have some PDU's that I literally have to run 2006-era Firefox browsers to get into these days. I don't want to have to deal with this in the future with the switches. If these switches are to be primarily accessed via a web browser without some kind of ssh option, direct console access, or other secure alternative, this seems like an important issue. Browsers are increasingly rejecting self-signed certificates as well.
Here's a link to my original question about this issue:
https://community.netgear.com/t5/Smart-Plus-Click-Switches/generating-certificates-with-GREATER-than-1024-bits/m-p/1659466/highlight/true#M10799
Thank you for your consideration to this idea/request.
--Cindy
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2018-10-29
01:34 PM
Submitted by
cme_lawoffices
on
2018-10-29
01:34 PM
I have recently started using team drives for Google. However, my file server only cloud syncs with Google personal drives. It does not have an option to add a team drive. Please add this functionality.
... View more
I want to make a time schedule for one POE port from 20:00 to 8:00 next day it should be disabled. This is now not possible. I have to make two schedules one from 20:00 to 23:59 and one from 0:00 to 8:00 but does not give the intende result since from 23:59 to 0:00 the port goes on. This because 24:00 is nota valid value and in fact it has to be valid.
Other option could be set with the schedule is the port has to switched of or on then the rule could be from 8:00 to 20:00 switch the port on other time switch it of . repeat this for every day.
... View more
See more ideas labeled with: