Showing ideas with status New Idea.
Show all ideas
Seems like we only have an all or nothing choice: "Allow IoT devices to see each other and access my local network" If I allow this then the whole purpose of the seperate SSID for IoT is lost. I want the IoT devices to see each other, but NOT access my local network. Specifically I have a Hubitat hub which needs to talk to two Android tablets, two Konnected boards and some TVs. They are all on the same SSID, and I would like them to stay removed from my local network. Seems the newer WiFi 6 router allows this to be configured via VLAN. Personally I'd prefer a method whereby access levels could be granted on a device by device basis. Thank you
... View more
See more ideas labeled with:
When building a guest network in Insight, it's important to be able to rate limit throughput per client so that no one client can consume all available bandwidth on that SSID/vLan. It can be accomplished via QoS on the APs themselves, but Inisght will not recognize those configs and the config change wouldn't be replicated to other APs. Additionally, the QoS config may be destroyed by Inisght upon config updates. Instructions for configuring QoS at the AP level: https://community.netgear.com/t5/Business-Wireless/How-do-I-limit-bandwidth-per-device-on-a-WAC730/m-p/1767103
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2021-12-23
09:45 AM
Submitted by
milkfromstone
on
2021-12-23
09:45 AM
What if we could have a superuser network that could cut across network isolation? Scenarion: - wireless 1: owner's network (superuser) - wireless 2: a network for guests, with network isolation Disired outcome: - How can wireless 1 see devices on wireless 2? - How can we ensure wireless 2 has no visibility of devices on wireless 1? I want W2 guests to be able to access Sonos, lights, fans that would be on W2, but not devices set on W1. All this while enabling W1 (superuser) to see IoT devices on any network.
... View more
See more ideas labeled with:
In the client section of the Insight App, it would be useful to see additional information against each device, for instance, which channel frequency are they using 2.4 to 5Ghz, what channel are they using, what 802.11xx mode are they using, what WPA mode did they authenticate with, the RSSI signal strength, are they using a private MAC address (on a modern phone) - adding fields (and others) such as these into the Client's page would help with diagnosing connection problems. Also would be good to be able to click on a client in the browser and see its history, so when it connect, disconnect, change AP if roamed, connect again etc, so we can see a history of the wireless client with relevant fields that will allow us to diagnose connectivity problems.
... View more
See more ideas labeled with:
Limiting the antenna power to levels like 100%, 50%, 25%, etc. is ridiculous and severly limits fine tuning it to the local radio enviroment. Please update to allow changing it to values from 1 dBm to 18 (20) dBm like a normal person.
... View more
See more ideas labeled with:
Would you please allow the WAC720 access points to be usable on Insight? Without Insight compatibility, impending discontinuation of Business Central will remove cloud management functionality from these devices that were purchased only 1 year ago. Thank you in advance!
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2022-10-25
05:17 AM
Submitted by
classicsound
on
2022-10-25
05:17 AM
Hello, I am just starting to work with the AV Line switches. I use them in a concert hall. There is an administrator and many users running the shows. For this, from my point of view, there needs to be some kind of user management. On the one hand, of course, the administrator with full access, but on the other hand, another account for status monitoring and assigning ports to VLANs, if that is necessary for a show. A user management with rights management would be perfect for this. Is such a feature already planned?
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2021-02-22
01:37 PM
Submitted by
IrishCornelius
on
2021-02-22
01:37 PM
Please add support for TLS 1.2 to GS108Tv2 switch range. Currently only TLS 1.0 is supported on firmware 5.4.2.35. TLS 1.0 is considered deprecated by IETF: https://tools.ietf.org/html/draft-ietf-tls-oldversions-deprecate-12 <extract> 4. Do Not Use TLSv1.0 TLSv1.0 MUST NOT be used. Negotiation of TLSv1.0 from any version of TLS MUST NOT be permitted. Any other version of TLS is more secure than TLSv1.0. TLSv1.0 can be configured to prevent interception, though using the highest version available is preferable. Pragmatically, clients MUST NOT send a ClientHello with ClientHello.client_version set to {03,01}. Similarly, servers MUST NOT send a ServerHello with ServerHello.server_version set to {03,01}. Any party receiving a Hello message with the protocol version set to {03,01} MUST respond with a "protocol_version" alert message and close the connection. Historically, TLS specifications were not clear on what the record layer version number (TLSPlaintext.version) could contain when sending ClientHello. Appendix E of [RFC5246] notes that TLSPlaintext.version could be selected to maximize interoperability, though no definitive value is identified as ideal. That guidance is still applicable; therefore, TLS servers MUST accept any value {03,XX} (including {03,00}) as the record layer version number for ClientHello, but they MUST NOT negotiate TLSv1.0. </extract>
... View more
See more ideas labeled with:
Hi, Please add SNMP support on the GC510PP, to monitor this device. Smaller devices do have SNMP support, but this more expensive model does not have SNMP support. I think SNMP support for managed switches is a MUST have, since they are used in "enterprice". Kind regards, Tim
... View more
See more ideas labeled with:
Hi,
is great to have the possibility to configure the VLAN management interface.
Thx!
Claudio
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2018-08-03
04:59 AM
Submitted by
sasha-london
on
2018-08-03
04:59 AM
Hi
I'm aware of the previous discusions/sugestions here about adding the ability to specify a managemet vlan on ProSAFE Plus lineup (e.g.GS108Ev3). While there are good alternatives higher up the line that do support this (GS108Ev3->GS108Tv2) I dont see a similar aternative for GS105PE - a-5 port passthrough POE switch. It would really be appreciated if this feature could be added to GS105PE. I think it would make the switch so much better. It does almost everything needed for this type of device - just lacking the management vlan.
Thanks,
Sasha
... View more
See more ideas labeled with:
I have two requests, 1) Being the most important and 2) being less important. 1) Per attached device real-time bandwidth monitor. Consider the scenario that a connect device is utilising too much bandwidth and slowing other users. You can’t easily identify the culprit at present. 2) Historical bandwidth and traffic stats, per attached device. Allowing you to identify large upload and downloads, etc., and View usage patterns. Thanks for the consideration.
... View more
See more ideas labeled with:
Status:
New Idea
Submitted on
2020-12-27
11:19 PM
Submitted by
nismo9132_net
on
2020-12-27
11:19 PM
I purchased both a GS305E and two GS308E switches and really like the performance and configuration functionality, but it's missing a key feature -a Configurable Management VLAN. Please add this feature because otherwise I'm likely going to return these switches to get something that supports them from another vendor for the same price point.
... View more
See more ideas labeled with:
As the core of LAN, L3 switch really needs DHCP reservation, which is indispensable. It's well-known that switch is the most stable hardware in network. It's more likely for a bare-metal server goes down than a switch does. If M4300 has DHCP reservation feature, we can transfer the DHCP server from a PC to the switch, which could enhance the stability and convenience for management of the network significantly. At present, in "System-Services-DHCP Pool Configuration", I have to create ONE "manual_pool" for EACH MAC-IP mapping. It's REALLY tedious and boring. I think you can add at least two features to improve the situation. 1. Re-design "System-Services-DHCP Pool Configuration-Type of binding-manual" in the web-gui, and allow people to add multiple MAC-IP-GATEWAY-DNS-NETBIOS mappings to one 'manual_pool'. For example: https://i.loli.net/2020/04/03/lotb2NgSHzwpqIL.png In this way, users can easily add or remove records by clicking the '+' or '-' button ahead of each line. 2. Add a new command to load an external text-based datebase which contains all the information stated above from a USB flash drive or tftp server. In this way, users can create and modify the text-based database using their favorite text-editor and then upload it to the switch. It would be great if the developers can add the features I stated above to M4300. Thanks a lot.
... View more
See more ideas labeled with:
I'm actually using an SRX 5308 router, which is tagged as EoL product. As there is no replacement for this router in Netgear catalog, I was wondering if a minimal firmware update implmenting TLS 1.2 (which is the minimum request for modern browsers) would be possible. So we could continue using the router and, first of all, connecting to managmenet interface via browser. Thanks in advance Luciano
... View more
See more ideas labeled with:
The GS110TP supports only a max SSL key length of 2048 bits. This is a real problem for modern PKI infrastructures where - at least - the CAs almost always use a 4096 bit key length.
Given that the GS110TP is still sold today I hope hat this could be corrected in a (near) future firmware update.
... View more
See more ideas labeled with:
It would be great to drill down on the daily Content Filtering Report, to see which connected clients tried to visit blocked sites. It would also be nice to offer parental controls for the device or connected client browsing history. The system is amazaing however it needs some additional features to be a reasonable solution for a work from home user with children.
... View more
See more ideas labeled with:
Please release an updated firmware with TLS 1.2/1.3 support, and the option to disable 1.0 and 1.1.
... View more
See more ideas labeled with:
Please consider using HTTPS for the web management of the GS1xxE line of switches.
Especially the smaller models need a secure way to configure them as there are no real replacements for in-field deployments outside special technical rooms where is no room to fit an entire rack into...
As the current state of security of many of the embedded or IoT thingis is sub-optimal it is crucial to prevent login credential sniffing via other pOwnd network devices within the same subnet.
Thanks,
Stefan Seide
... View more
See more ideas labeled with:
Currently (and historically) Netgear does not always show all connected devices. This leads to a loss of user confidence in the web interface and app's ability to reflect the current state. Example- my currently connected NAS is not listed in the Attached Devices even though I previously reserved an IP address for it under Advanced -> LAN Setup. (The NAS indeed is using this reserved address.) The NAS is a wired and active connection but is only visible under Advanced->Access Control-> "View list of allowed devices not currently connected to the network". Notes- 1) other active devices are also listed as inactive. 2) normally Access Control is not implemented - this is the only visibility to devices known to be active. Use case- provide more aggressive active device polling.
... View more
See more ideas labeled with: